Carla Adriana Theis Soares Diehl

Pós-doutorado

Formação complementar

Idiomas

Áreas de atuação

Participação em eventos

Participação em bancas

Produções bibliográficas

• DIEHL, I.L. ; THEIS SOARES DIEHL, C.A. ; SCHIFELBAIN DE LIMA, T.R. ; ROSAURO CLARKE, T.G. ; TORRES PIZA PAES, M. . Residual Stress Measurements in Tensile Armours of Flexible Pipes by the Contour and X-Ray Diffraction Methods. EXPERIMENTAL MECHANICS , v. 64, p. 565-574, 2024.

• RAMOS, F. D. ; MOSCOSO, M. F. C. ; REGUL, A. ; DIEHL, I. L. ; SOARES, C. A. T. . Nitriding of Steel AISI D2 After Deep Cryogenic Treatment. METAL SCIENCE AND HEAT TREATMENT , v. 65, p. 285-291, 2023.

• DA SILVA, D. S. ; LUTCKMEIER, F. ; DIEHL, I. L. ; Diehl, C. A. T. S. ; DE LIMA, T. R. S. ; CLARKE, T. G. R. ; PAES, M. T. P. . Hole-Drilling Method for Deep Residual Stress Measure in Tensile Armour Wires. EXPERIMENTAL MECHANICS , v. 2022, p. 1-14, 2022.

• DALCIN, RAFAEL LUCIANO ; MARQUES DE MENEZES, VALCIR ; FONSECA OLIVEIRA, LEONARDO ; DA SILVA, CARLOS HENRIQUE ; KLEIN DAS NEVES, JULIO CESAR ; Theis Soares Diehl, Carla Adriana ; DA SILVA ROCHA, ALEXANDRE . Improvement on pitting wear resistance of gears by controlled forging and plasma nitriding. Journal of Materials Research and Technology-JMR&T , v. 18, p. 4698-4713, 2022.

• DALCIN, RAFAEL LUCIANO ; OLIVEIRA, LEONARDO FONSECA ; Diehl, Carla Adriana Theis Soares ; DA SILVA ROCHA, ALEXANDRE . Response of a DIN 18MnCrSiMo6-4 Continuous Cooling Bainitic Steel to Different Plasma Nitriding Gas Mixtures. Materials Research-Ibero-american Journal of Materials , v. 23, p. e20200269-11, 2020.

• ZOTTIS, JULIANA ; Soares Diehl, Carla Adriana Theis ; Rocha, Alexandre da Silva . Evaluation of experimentally observed asymmetric distributions of hardness, strain and residual stress in cold drawn bars by FEM-simulation. Journal of Materials Research and Technology-JMR&T , v. 7, p. 469-478, 2018.

• Diehl, Carla Adriana Theis Soares ; Rocha, Alexandre da Silva ; EPP, JÉRÉMY ; ZOCH, HANS-WERNER . Experimental Analysis of Residual Stresses in Pre-Straightened SAE 1045 Steel. Materials Research-Ibero-american Journal of Materials , v. 20, p. 1554-1562, 2017.

• Dias, Vinicius Waechter ; ZOTTIS, JULIANA ; Soares, Carla Adriana Theis ; Souza, Tomaz Fantin de ; Rocha, Alexandre da Silva . Study of the Influence of Anisotropy on the Residual Stresses Generated in the Wire Drawing Process of an AISI 1045 Steel. REVISTA COLOMBIANA DE MATERIALES , v. 1, p. 130-137, 2014.

• ZOTTIS, J. ; SOARES, C. A. T. ; PAVLAK, RAFAEL PAINI ; SOUZA, Tomaz Fantin de ; DIAS, VINICIUS WAECHTER ; ROCHA, ALEXANDRE DA SILVA . SIMULAÇÃO NUMÉRICA DAS TENSÕES RESIDUAIS GERADAS NO PROCESSO DE TREFILAÇÃO PARA DIFERENTES PARÂMETROS DE PROCESSO. TECNOLOGIA EM METALURGIA, MATERIAIS E MINERAÇÃO (IMPRESSO) , v. 11, p. 34-40, 2014.

• Souza, Tomaz Fantin de ; Soares, Carla Adriana Theis ; ZOTTIS, JULIANA ; NUNES, RAFAEL MENEZES ; Rocha, Alexandre da Silva ; HIRSCH, THOMAS . Comparison between Neutron Diffraction measurements and numerical simulation of residual stresses of a Wire-Drawing process. Materials Research-Ibero-american Journal of Materials , v. 16, p. 508-514, 2013.

• ZOTTIS, J. ; FREITAS, L.M. ; Soares, Carla Adriana Theis ; SOUZA, T. F. ; COLOMBO, T. C. A. ; ROCHA, A.S. . Influência do ângulo e do coeficiente de atrito nas tensões residuais geradas na trefilação de barras de aço AISI 1045. ESTUDOS TECNOLÓGICOS (ONLINE) , v. 9, p. 54-62, 2013.

• NUNES, R. M. ; Rocha, AS ; SOUZA, Tomaz Fantin de ; SOARES, C. A. T. ; Tekkaya A.E ; Hirsch, Thomas . Experimental characterization and simulation of a wire drawing process and related distortion potentials∗. HTM Journal of Heat Treatment and Materials , v. 68, p. 135-141, 2013.

• SOARES, C. A. T. ; ZOTTIS, J. ; BITTENCOURT, J. P. ; PAVLAK, R. P. ; SOUZA, T. F. ; ROCHA, A. S. . ANÁLISE DAS POSSÍVEIS CAUSAS DE DISTORSÕES GERADAS NO PROCESSO DE TREFILAÇÃO DE BARRAS DE AÇO AISI 1045. ABM Proceedings , v. 68º, p. 886-898, 2013.

• SOARES, C. A. T. ; Rocha, Alexandre da Silva ; Hänisch, Stephan ; Coser, Tiago Brun ; Souza, Tomaz Fantin de . Simulação computacional de um processo de trefilação para produção de barras redondas de aço AISI 1045. REM. Revista Escola de Minas (Impresso) , v. 64, p. 513-518, 2011.

• DIAS, VINICIUS WAECHTER ; SOARES, C. A. T. ; ZOTTIS, JULIANA ; ROCHA, ALEXANDRE DA SILVA . Análise das transformações nas tensões residuais durante o processo de fabricação de eixos automotivos. In: 22º CBECIMAT, 2016. 22º Congresso Brasileiro de engenharia e ciência dos materiais, 2016.

• ROCHA, A.S. ; SOARES, C. A. T. ; ZOTTIS, J. ; DIEHL, I. L. ; DIAS, V. W. . Influence Of Friction And Die Geometry On Residual Stresses Generated In A Cold Drawing Process. In: CONGRESSO BRASILEIRO DE ENGENHARIA DE FABRICAÇÃO, 2015, Salvador. CONGRESSO BRASILEIRO DE ENGENHARIA DE FABRICAÇÃO, 2015.

• ZOTTIS, JULIANA ; PAVLAK, RAFAEL PAINI ; Soares, Carla Adriana Theis ; Dias, Vinicius Waechter ; Rocha, Alexandre da Silva . INFLUÊNCIA DE HETEROGENEIDADES DE PROCESSO NA GERAÇÃO DE TENSÕES RESIDUAIS. In: 8° CONGRESSO BRASILEIRO DE ENGENHARIA DE FABRICAÇÃO SENAI CIMATEC, 2015, Salvador. 8º Congresso Brasileiro de Engenharia de Fabricação - 8º COBEF, 2015. v. 8°.

• Dias, Vinicius Waechter ; Soares, Carla Adriana Theis ; KEMMERICH, H. T. ; ZOTTIS, JULIANA ; Rocha, Alexandre da Silva . Simulação Computacional das Influências de uma Linha de Segregação no Núcleo de uma Barra Trefilada. In: 8° CONGRESSO BRASILEIRO DE ENGENHARIA DE FABRICAÇÃO SENAI CIMATEC, 2015, Salvador. 8° CONGRESSO BRASILEIRO DE ENGENHARIA DE FABRICAÇÃO, 2015. v. 8°.

• SOUZA, T. F. ; SOUZA, V. M. ; MILKE, E. C. ; ROCHA, A.S. ; SOARES, C. A. T. ; COSER, T.B. ; WOLFART JUNIOR, M. . TREFILAÇÃO DE AÇOS BAIXO CARBONO ATRAVÉS DE MÁQUINA UNIVERSAL DE ENSAIOS. In: 6º SEMINÁRIO DE TREFILAÇÃO: ARAMES, BARRAS E TUBOS DE METAIS FERROSOS E NÃO FERROSOS, 2015, Rio de Janeiro. SEMINÁRIO DE TREFILAÇÃO: ARAMES, BARRAS E TUBOS DE METAIS FERROSOS E NÃO FERROSOS, 2015. v. 6.

• SOARES, C. A. T. ; ZOTTIS, J. ; BITTENCOURT, J. P. V. ; PAVLAK, R. P. ; SOUZA, T. F. ; ROCHA, A.S. . Análise da possíveis causas de Distorções geradas no processo de trefilação de barras de aço AISI 2045. In: Congresso Anual da Associação Brasileira de Metalurgia, 2013, Belo Horizonte. Anais do 68 Congresso Anual da Associação Brasileira de Metalurgia, 2013. p. 886-898.

• Dias, Vinicius Waechter ; Soares, Carla Adriana Theis ; Rocha, Alexandre da Silva . Os Efeitos De Diferentes Processos De Corte Na Preparação De Geratrizes Para Forjamento. In: 33º SENAFOR, 2013, Porto Alegre. Anais do 33º SENAFOR: 17ª Conferência Internacional de Forjamento, 2013.

• COLOMBO, T. C. A. ; MARTINS, V. ; SOUZA, T. F. ; SOARES, C. A. T. ; SHAEFFER, L. . Simulation of Microstructure Evolution During Hot Working. In: 67º Congresso da ABM, 2012, Rio de Janeiro. Anais do 67 Congresso Internacional da ABM, 2012. p. 1386-1393.

• SOARES, C. A. T. ; SOUZA, T. F. ; COSER, T.B. ; FREITAS, L.M. ; ROCHA, A.S. . Simulação Numérica das Tensões Residuais Geradas no Processo de Trefilação para Diferentes Ângulos de Fieira. In: Congresso Anual da Associação Brasileira de Metalurgia, 2011, São Paulo. Anais do 66 Congresso Anual da Associação Brasileira de Metalurgia, 2011.

• ROCHA, A.S. ; NUNES, R. M. ; SOUZA, T. F. ; SOARES, C. A. T. ; HAENISCH, S. ; TEKKAYA, A. E. ; HIRSCH, T. . Experimental characterization and simulation of a wire drawing process and related distortion potentials. In: IDE 3rd International Conference on Distortion Engineering 2011, 2011, Bremen. Proceedings of the IDE 3rd International Conference on Distortion Engineering, 2011. p. 229-237.

• Dias, Vinicius Waechter ; Soares, Carla Adriana Theis ; Rocha, Alexandre da Silva . Os Efeitos De Diferentes Processos De Corte Na Preparação De Geratrizes Para Forjamento. 2013. (Apresentação de Trabalho/Congresso).

Projetos de pesquisa

• 2022 - 2022

  Desenvolvimento de metodologias de aplicação de ultrassom phased array para inspecionar soldas em altas temperaturas, Situação: Concluído; Natureza: Pesquisa. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / CLARKE, T. G. R. - Coordenador.

• 2019 - Atual

  Análise de Tensões Residuais em Armaduras de Dutos Flexíveis: Métodos Elétricos e Eletromagnéticos, Descrição: O projeto tem como objetivo principal a avaliação de tensões residuais em armaduras de tração e de pressão de dutos flexíveis a partir de análise comparativa entre vários métodos de medição de modo a possibilitar a identificação das vantagens e limitações de cada método para aplicação em caracterização de tensões de dutos flexíveis.. , Situação: Em andamento; Natureza: Pesquisa. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Igor Luis Diehl - Integrante / Toni Roger Schifelbain de Lima - Integrante / CLARKE, T. G. R. - Coordenador.

• 2016 - 2019

  Tratamentos superficiais de aços para aumento da vida de ferramentas de conformação, Situação: Concluído; Natureza: Pesquisa. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / ROCHA, ALEXANDRE DA SILVA - Coordenador.

• 2010 - 2013

  Investigação e Melhoria de uma rota de fabricação de trefilação a Têmpera por Indução (Projeto BRAGECRIM nº 1117/09), Projeto certificado pelo(a) coordenador(a) Alexandre da Silva Rocha em 15/04/2023., Situação: Concluído; Natureza: Pesquisa. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Alexandre da Silva Rocha - Coordenador.

Projetos de desenvolvimento

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.

• 2010 - 2014

  Investigation and improvement of a manufacturing process chain from cold drawing processes to induction hardening, Projeto certificado pela empresa Gerdau Cosigua em 10/06/2016., Descrição: Projeto Bragecrim 001/2009. Manufacturing processes in general consist of materials solidification processes, metal forming processes and more than one straightening process, machining and heat treatment processes. Machining and final straightening is then necessary to guarantee the required shape and dimensions of machine parts. Few attempts are made to optimize products over more than one production step and difficulties arise from the fact that single production steps in a world market take place in different countries around the world. Cold forming processes are energy efficient and clean and are used in production processes with an increasing number. Cold forming on the other side significantly changes materials properties and cold formed automotive parts need a surface heat treatment or have to be through hardened completely to fulfill strength requirements. An improvement of properties during one production step consequently can result in problems in the next, one of the following or finally in the last manufacturing step. Components manufactured in this way show a broad band of distortions, which have to be removed by additional expensive machining operations. The transmission of distortion potentials from one manufacturing step to the other in a cold drawing process with additional induction hardening will be analyzed experimentally and partially modeled. A DoE-plan (design of experiments) of main affecting parameters will be used to identify effects and correlations. A reduction of one or more manufacturing operation as e.g. additional straightening and/or machining will be expected.. , Situação: Concluído; Natureza: Desenvolvimento. , Integrantes: Carla Adriana Theis Soares Diehl - Integrante / Tomaz Fantin de Souza - Integrante / Alexandre da Silva Rocha - Coordenador / Rafael Menezes Nunes - Integrante / ZOTTIS, JULIANA - Integrante / Vinicius Waechter Dias - Integrante., Financiador(es): Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - Auxílio financeiro.